Pulleys

2" O.D. x 1.350" wide hub x .375" bolt bore. Made of nylon with steel hub. Pulley sometimes used to ride on 1" diameter steel round bar. Rides on unsealed ball bearings. Made in USA!

2.75" OD x 1" Hub x .375" Bolt Bore - Nylon Cable Idler Pulley. Unsealed ball bearing. Maximum cable diameter: 3/16". Made in USA!

4" O.D. x 1" Hub x .375" Bolt Bore - Nylon Cable Pulley replaces selectorized machines that use 1/8" O.D. to 1/4" O.D. cable as the drive medium. Rides on sealed ball bearing and made of aircraft-quality nylon. Made in USA!

4.5" O.D. x 1" Hub x .500" oversized Bolt Bore - Nylon Cable Pulley. Sealed ball bearing. Maximum cable diameter: 1/4". Made in USA!

4.5" OD x 1.5" EXTRA WIDE Hub x .375" Bolt Bore - Nylon Cable Pulley. Sealed ball bearing. Maximum cable diameter: 1/4". Made in USA!

4.5" O.D. x 1.5" Hub x .375" Bolt Bore - Nylon Pulley for 1" Kevlar Belt. Effective belt contact diameter is 4". Sealed ball bearing. Made in USA!

5.5" O.D. x .710" Hub x .393"(10 mm)Bolt Bore Chrome Plated Steel Cable Pulley - Sealed ball bearings. Maximum Cable Diameter: 1/4".

This pulley does NOT have a protruding hub! Washers or spacers must be used on both sides of pulley to isolate it to keep from rubbing against mounting plates. Uses a 10mm bolt. A 3/8" bolt may be used but it will be slightly loose.

Solid steel construction beautifully chrome plated. Bearings have steel races with plastic seal covers.

Made in USA!

3.5" (90 mm) O.D. x .864" (23 mm) Hub x .393" (10 mm) Bolt Bore Aluminum Cable Pulleys

Key Features

Machined from solid 6061 T6 aircraft aluminum

Sealed ball bearing with steel hubs

Maximum cable size is 1/4" (including jacket coating)

Pulley groove depth is .270" thus making the effective pulley diameter 3" approx.

Pulley itself is (.787") 20 mm wide, so the .864" wide hub sticks out a small amount on each side to clear mounting brackets

Not for use with bare cable

All metric dimensions are nominal and rounded up the nearest whole number - for the most accurate dimensions use the inch measurements provided

Beautiful polished finish!

4.300" (110 mm) OD x 1.780" (46 mm) Hub x .393" (10 mm) Bore Nylon Super Wide Groove Cable Pulleys with Wide Hub can be used in place of a swivel pulley. Applications that call for a swivel pulley do so because the pulley groove must remain aligned with cable force vector, or it will derail. These pulleys have a deep and wide cable groove, so if mounted statically, they can tolerate a wide angle of misalignment before derailing the cable.

Click small thumbnail to the left to enlarge angle shot of pulley.

Key Features

Super wide cable groove allows variable cable alignment applications without derailing

Typically used as a static mounted pulley in place of a swivel narrow groove pulley (eg cable crossover machine)

Made of reinforced composite nylon

Sealed ball bearing with nylon hubs

Pulley groove depth is .707" thus making the effective pulley diameter 3" approx.

Pulley itself is (1.638") 42 mm wide, so the 1.790" wide hub sticks out a small amount on each side to clear mounting brackets

Not for use with bare cable

All metric dimensions are nominal and rounded up the nearest whole number - for the most accurate dimensions use the inch measurements provided

Maximum cable size: 1/4" including jacket

Great for applications using nylon rope

Rare item!

4.300" (110 mm) OD x .864" (23 mm) Hub x .393" (10 mm) Bore Nylon Super Wide Groove Cable Pulleys with Narrow Hub can be used in place of a swivel pulley. Applications that call for a swivel pulley do so because the pulley groove must remain aligned with cable force vector, or it will derail. These pulleys have a deep and wide cable groove, so if mounted statically, they can tolerate a wide angle of misalignment before derailing the cable. Unlike the other super wide cable pulley we offer, this one has a narrow hub for custom shimming for "deep dish" mounting. The hub is so narrow that it does not protrude from the sides of the pulley, therefore special mounting considerations must be made in order for proper clearance. For example, this pulley could be mounted at the end of a length of 1" steel round stock. To put it another way, this pulley is not suitable for mounting between two bracket plates without shimming.

Click on thumbnail above to enlarge angled shot of pulley

Key Features

Super wide cable groove allows variable cable alignment applications without derailing

Typically used as a static mounted pulley in place of a swivel narrow groove pulley (eg cable crossover machine)

Made of reinforced composite nylon

Sealed ball bearing with steel hubs

Pulley groove depth is .707" thus making the effective pulley diameter 3" approx.

Pulley itself is (1.638") 42 mm wide,with a narrow hub .864" wide, which does not stick out on either side of the pulley

Not for use with bare cable

All metric dimensions are nominal and rounded up the nearest whole number - for the most accurate dimensions use the inch measurements provided

Maximum cable size: 1/4" including jacket

Great for applications using nylon rope

Rare item!